ARC Racing

DJ-18-930 3-Staged J-Pipe Header I.D. .930" for the GX200/Clone/ Predator 212cc/ Predator 224CCThis header is designed to fit the Honda/ Clone/ Predator engines. Uses RLV 1-5/16 Silencers

The new "660" Drag series billet flywheel for the Honda GX200, Clone 196, Ducar 196/212, Tillotson 196/212, Predator Ghost 212 and Predator 224cc engines from ARC Racing. Features a finless drag...

Titanium retainer and steel keeper set for aftermarket 5.5mm stainless valves on the  5.5mm GX200, 196cc Clone, 1st Gen Predator and Predator Hemi(will not work on 3rd Gen Predator mm valves)...

*Depending on availability, pushrods may be black anodized or uncoated. This is a pair of the "Do It Yourself" pushrod kit which features a 5.75" long shaft with 2 ball type ends. The rods are made...

New Stainless Steel Pushrods for the BSP/Clone/GX200/ non-Hemi Predator Engines. Stock Length. Price is for 2 pushrods

Low lift square tip rocker arm for the BSP/Clone engines

Kit contains two .1 mm shims and two .2 mm shims

Rubber Valve Cover Gasket For The BSP Clone 196cc Engines. Seal better and last longer than the traditional cork gaskets. "May" work on the newest Gen3 Predator 212cc engines with 27/25 valves and...

Crank Bearing for our 6057 and 6058 Sidecovers

Predator MLS head gasket .027" thick by 70mm(2.756") bore. MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and...

Predator MLS head gasket .018" thick by 70mm(2.756") bore. MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and...

PVL ignition coil 555681 has a 12,000 RPM limit! For use on Animal, World Formula, and with the ARC PVL billet flywheels. You must use the specific PVL flywheel with this coil  

The new 6689 billet flywheel from ARC Racing has an ultra low drag fin design that will greatly reduce air drag on your AKRA racing engine, while still moving enough air for cooling. Less air drag on...

2 Pack of 22Lb Valve Springs.These springs are recommended for use with the stock retainers. 22lbs @ .850"

2 Pack of 26Lb "White" Springs. Use as intake spring when using stock intake valve and ARC DJ-1046 Spring retainer. Use as Heavy spring for intake and exhaust when using our stainless (DJ-1121,22 and...

*Depending on availability, pushrods may be black anodized or uncoated. *SOLD INDIVIDUALLY* .187 Diameter chromoly stock length used in Fits Honda GX200, 196cc Clone, 1st and 3rd generation Harbor...

1.3 ratio GX200 / Clone Billet Steel Rocker SetReplaces the stock rockers with 1.3:1 ratio billet steel rocker arms, heavy duty billet steel rocker studs, lash caps, rocker pivots, adjuster nuts, set...

New and Improved 1.3 Ratio Roller Tip Rockers for the Clone and Fits Honda GX160/200/Predatro 212 NON-Hemi Engines Precision machined from chromoly steel with hardened roller tips and shafts. Dyno...

New and Improved 1.2 Ratio Roller Tip Rockers for the Clone and Fits Honda GX160/200/Predator 212 NON-Hemi Precision machined from chromoly steel with hardened roller tips and shafts. Dyno tested to...

The Gage Black Venom Roller Rocker Arms are a high-quality component designed to enhance the performance of your engine. Fits Honda GX160/GX200, Predator 212/224 Non-Hemi, 196cc Clones, and Tillotson...

14x1.5mm Extended Starter Nut for Honda /196 Clone / Predator 212 and Yamaha, 66.5mm long

GX200/Clone/Predator 212 Stock Ignition Coil Bolt

BSP / Clone Stock Rocker Arm

Original Stock Part On / Off Switch for GX200 / Clone Engines

Standard Stock Flywheel key Fits Fits Honda GX160/200/240/270/390 Predator 196/212/301/420 196cc Clones and many other Chinese OHV engines

Flat top piston for the "Hemi" Predator engine. This 70mm(2.756") piston comes complete with rings, .709" OD wrist pin, and clips. This piston has an approximately .020" shorter compression height...

ARC Rod Bolt Set, 1-1/4" LG HD This rod bolt set is made from top quality materials, the bolts are high tensile strength. In the pictures, the threads are enclosed in plastic tubing for protection...