Engines and Performance Parts

Predator 212cc / Clone 196cc Air Filter Kit

This kit will fit Predator 212cc, Honda GX160, GX200 engines, and most Chinese 6.5HP OHV Clone engines. This contains the parts included in our performance kits that use the standard adapter. (1) Angled Air Filter 3-1/2 x 4 (1) Billet Aluminum...

Go Kart Weiner Pipe AKRA Legal w/ Standard Muffler Predator 212cc

AKRA legal Weiner Pipe for Honda, Clones, and Predator Engines. Fits GX160, GX200, Clones, and Predator 212cc motors. Weenie pipe comes with a standard, non-restricted, screw-on muffler! THIS IS A SMALL DIAMETER AKRA SPEC PIPE FOR GO KART RACING An...

8 Degree Offset Key

Offset Flywheel Key for GX200 / GX160 / Clones / Predator Offset Flywheel Key for GX200 / GX160 / Clones / Predator These keys are extremely popular and a favorite for racers using our 6619 and 6625 flywheels that want to adjust and tune timing for...

Predator 212cc Go Kart Kit - Stage 1 - Non-Hemi

Non-Hemi Predator 212cc Go Kart Stage 1 Performance Kit This is a stage 1 performance kit to put on any non-hemi Predator 212cc motor for a go kart. Make sure you use a billet flywheel if you have taken the governor off of your motor! Kit...

Angled Air filter 3-1/2" x 4" x 2-7/16"

Fabric Air Filter The standard angled air filter used in most 4 cycle karting engines. 3-1/2" x 4" with a 20 degree angle. The inside diameter of the mounting flange is 2-7/16". Most OHV kart engines will require an angled air filter! 3-1/2" X...

Mini Bike Pipe w/ Muffler - Under seat style

Tighter bend pipe that shoots straight behind a mini bike underneath your seat. Comes with a screw on muffler. For Honda Clone GX160, GX200, Predator 212cc. Perfect for mini bikes so the pipe doesn't burn your leg. 8" clearance from motor mount to pipe...

1" Go Kart Exhaust w/ Screw on Muffler Predator 212cc/Clone

1" Go Kart Exhaust w/ Screw on Muffler Predator 212cc/Clone 212cc, 196cc EnginesNo drilling required! Total length from end to end with muffler screwed on is approximately 13".Height of pipe from mounting area to screw on end is approximately 5" Due to...

Predator 212cc Go Kart Kit - Stage 1 - Hemi

Make sure you use a billet flywheel if you have taken the governor off of your motor!Kit includes: (1) angled air filter(1) air filter adapter(1) choke hold bracket(1) heavy rubber gasket(1) long carburetor stud(1) "140" emulsion tube(1) .036 jet(1)...

Foam Pre-Filter Red 3-1/2"x5"

Race Ready/CNC Bored Box Stock Carb

Our "615" Box Stock class carb. Airflow has been significantly increased by opening and reshaping the Venturi using a CNC machine - the same technology we use to bore our connecting rods. The fuel circuit is set to where we run them ourselves so you can...

Predator 212cc Go Kart Kit - Stage 2 - Non-Hemi

This is a stage 2 performance kit to put on any non-hemi Predator 212cc motor for a go kart. Make sure you use a billet flywheel if you have taken the governor off of your motor!Kit includes:(1) angled air filter(1) air filter adapter(1) choke hold...

Box Stock Header and Muffler Honda/Clone Predator 212cc

ARC's header and muffler kit for the AKRA/WKA clone Box Stock class. Looking at the picture above, it is easy to see what sets ARC's header apart. The flange is funneled into the header pipe so exhaust gases flow smoothly out of the exhaust port...