ARC Racing

All sizes of main jets for Predator Engines, Honda Clone Engines, Box Stock Engines and other Chinese Clones. These can be used as replacements for stock or upgrades in performance applications...

OHV 212cc Bare Cylinder Head. This is a replacement head for the Hemi 212 or the Fits Honda /Clone engines. Can be used on Predator 212 Non-Hemi blocks if the dowel on holes are drilled to 11MM's...

*Depending on availability, pushrods may be black anodized or uncoated. Set of (2) .187" Diameter, 5.260" long, chromoly stock length pushrods used in GX200, 196cc Clone, BSP, and 1st and 3rd...

*Depending on availability, pushrods may be black anodized or uncoated. This is a pair of the "Do It Yourself" pushrod kit which features a 5.75" long shaft with 2 ball type ends. The rods are made...

New Stainless Steel Pushrods for the BSP/Clone/GX200/ non-Hemi Predator Engines. Stock Length. Price is for 2 pushrods

Exhaust Spring Ultralite Retainer. NOT RECOMMENDED FOR SPRINGS OVER 10.8 POUNDS

Intake Spring Ultralite Retainer. NOT RECOMMENDED FOR SPRINGS OVER 10.8 POUNDS

Low lift square tip rocker arm for the BSP/Clone engines

HONDA   GX200 UT1 thin ring-short skirt FLAT TOP piston standard bore. This line of pistons by Honda, the UTI pistons are lighter, with shorter skirt lengths and the rings...

Rubber Valve Cover Gasket For The BSP Clone 196cc Engines. Seal better and last longer than the traditional cork gaskets. "May" work on the newest Gen3 Predator 212cc engines with 27/25 valves and...

MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and corrosion resistance properties. 

MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and corrosion resistance properties.  

Dyno testing has shown as much as 4 tenths/HP and an average of 2 tenths/HP gain using Low Tension Ring Sets over stock OEM rings. The low tension rings are heat treated in a special...

TECH KIT FEATURES:  Contains - Main Jet .042 No-Go Gauge; -Pilot Jet .019 No-Go Gauge; -Emulsion Tube .066 No-Go GaugeBox Stock Project : Carburetor - Choke Bore .810 No-Go Gauge   -...

This Bracket designed to check Cam lift in Clone engines. It uses a Dial Indicator (not included)  

 .010 Valve Spring Shim

6615 Drag PVL Flywheel. For use with the Fits Briggs and Stratton digital PVL ignition system on the Fits Honda GX200/196cc Clone, Tillotson 196/212/225/228/236 engines. Finnless Flywheel designed...

Oil Drain plug with washer. Fits GX160 GX200 Clone BSP and Predator 212 engines.

PVL ignition coil 555681 has a 12,000 RPM limit! For use on Animal, World Formula, and with the ARC PVL billet flywheels. You must use the specific PVL flywheel with this coil  

The new 6689 billet flywheel from ARC Racing has an ultra low drag fin design that will greatly reduce air drag on your AKRA racing engine, while still moving enough air for cooling. Less air drag on...

2 Pack of 22Lb Valve Springs.These springs are recommended for use with the stock retainers. 22lbs @ .850"

For Modified BSP, Clone, GX200, Predator 212, and Yamaha F200. 36lbs at .850 installed height and coil bind at .450. Requires part number ARC_DJ-1046 retainer and keeper kit. May require head...

2 Pack of 26Lb "White" Springs. Use as intake spring when using stock intake valve and ARC DJ-1046 Spring retainer. Use as Heavy spring for intake and exhaust when using our stainless (DJ-1121,22 and...

1.3 ratio GX200 / Clone Billet Steel Rocker SetReplaces the stock rockers with 1.3:1 ratio billet steel rocker arms, heavy duty billet steel rocker studs, lash caps, rocker pivots, adjuster nuts, set...

This CNC bored .675 carb is designed for the Stock Appearing or Outlaw class and offers a special built ultra thin throttle shaft and knife edge butterfly that greatly increases air flow. Reworked...

New and Improved 1.3 Ratio Roller Tip Rockers for the Clone and Fits Honda GX160/200/Predatro 212 NON-Hemi Engines Precision machined from chromoly steel with hardened roller tips and shafts. Dyno...

New and Improved 1.2 Ratio Roller Tip Rockers for the Clone and Fits Honda GX160/200/Predator 212 NON-Hemi Precision machined from chromoly steel with hardened roller tips and shafts. Dyno tested to...

The Gage Black Venom Roller Rocker Arms are a high-quality component designed to enhance the performance of your engine. Fits Honda GX160/GX200, Predator 212/224 Non-Hemi, 196cc Clones, and Tillotson...