ARC Racing

All the parts your need to build your engine into a high performance engine. Turn your 6.5 horsepower Clone/Predator engine into a 14 to 15+ horsepower screamer. Target rpm range is 7500-7800 rpms...

OHV 70MM (2.756") Cylinder assembly. This is a Hemi replacement block that uses the Fits Honda /Clone cams, sidercover and top plate. Will require modification to upper and lower dowel pin holes to...

*Depending on availability, pushrods may be black anodized or uncoated. This is a pair of the "Do It Yourself" pushrod kit which features a 5.75" long shaft with 2 ball type ends. The rods are made...

New Stainless Steel Pushrods for the BSP/Clone/GX200/ non-Hemi Predator Engines. Stock Length. Price is for 2 pushrods

Kit contains two .1mm shims and two .2mm shims

Predator MLS head gasket .018" thick by 70mm(2.756") bore. MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and...

Oil Drain plug with washer. Fits GX160 GX200 Clone BSP and Predator 212 engines.

Thick rubber air box to carb gasket for the GX390 and Predator 301/420cc engines

ARC Top Plate/Throttle Control Linkage Assembly for the Fits Honda GX270, GX340, GX390 and Predator 301cc and 420cc Engines. This Part is made with quality components and the same attention to detail...

The new 6695 billet flywheel from ARC Racing for the Predator 212 NON-Hemi has an ultra low drag fin design that will greatly reduce air drag on your racing engine, while still moving enough air for...

2 Pack of Heavy Duty Valve Springs for Honda GX240, GX270, GX340, & GX390.Approx 50 lbs at 1.125 installed height, 42lbs at 1.2, with 110 lb open pressure (.375 lift).

2 Pack of 22Lb Valve Springs.These springs are recommended for use with the stock retainers. 22lbs @ .850"

For Modified BSP, Clone, GX200, Predator 212, and Yamaha F200. 36lbs at .850 installed height and coil bind at .450. Requires part number ARC_DJ-1046 retainer and keeper kit. May require head...

2 Pack of 26Lb "White" Springs. Use as intake spring when using stock intake valve and ARC DJ-1046 Spring retainer. Use as Heavy spring for intake and exhaust when using our stainless (DJ-1121,22 and...

*Depending on availability, pushrods may be black anodized or uncoated. *SOLD INDIVIDUALLY* .187 Diameter chromoly stock length used in Fits Honda GX200, 196cc Clone, 1st and 3rd generation Harbor...

Predator MLS head gasket .018" thick by 72mm(2.835") bore. MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and...

1.3 ratio GX200 / Clone Billet Steel Rocker SetReplaces the stock rockers with 1.3:1 ratio billet steel rocker arms, heavy duty billet steel rocker studs, lash caps, rocker pivots, adjuster nuts, set...

New and Improved 1.3 Ratio Roller Tip Rockers for the Clone and Fits Honda GX160/200/Predatro 212 NON-Hemi Engines Precision machined from chromoly steel with hardened roller tips and shafts. Dyno...

***MUST USE WITH DJ-1070CM PUSH RODS. Rocker Arms, Roller tip for the Habor Freight Hemi Predator 212 from NR Racing. Machined from chrome moly steel in 1.2/1 ratio. Hardened roller tips and...

SFI certified billet aluminum flywheel for Kohler CH270 or the hemi head Harbor Freight Predator 212cc engine (cast aluminum valve cover). Harbor Freight model #60363. The keyway is fixed and the...

Original Stock Part On / Off Switch for GX200 / Clone Engines

Standard Stock Flywheel key Fits Fits Honda GX160/200/240/270/390 Predator 196/212/301/420 196cc Clones and many other Chinese OHV engines

Stock replacement valve cover gasket for the Predator HEMI 212cc engine.

Flat top piston for the "Hemi" Predator engine. This 70mm(2.756") piston comes complete with rings, .709" OD wrist pin, and clips. This piston has an approximately .020" shorter compression height...

Ultra-Light SFI Certified Billet Aluminum Flywheel for the Predator Hemi Weighs 1.75 LBS Stock Diameter, Lightest Flywheel Available. This flywheel is made from same quality materials and with the...

Ultra-Light SFI Certified Billet Aluminum Flywheel for the Predator 212. Weighs 1.75 LBS Stock Diameter, Lightest Flywheel Available. Fits the old style non "hemi" head Predator 212 with tin sheet...

ARC +.040" long rod to utilize the Hemi Predator flat top piston (ARC_DJ-1285PH) in a non-hemi Predator engine (WILL NOT WORK IN HEMI BLOCK without modification). 3.343" center to center for a 1.188"...