ARC Racing

Rod Bolt Set, 1" LG HP Torque bolts to 170 in/lbs

6611-VG for the Briggs Vanguard Fits V-Twin, Mod 30, Mod 35, Mod 38We Recommend Using the #808726 Starter for these Applications. Coil Brackets Included with Purchase and Mounting Hardware

ARC's SFI certified billet aluminum flywheel for the Briggs and Stratton vertical crankshaft Intek V-Twin models 40 & 44 engine often used in lawnmower racing. The 6611 flywheels are designed as...

Stroker Animal Flywheel Hub  

SFI certified billet flywheel for the Briggs 5hp flathead. 5-3/4" diameter(3hp) adjustable timing flywheel with rare earth magnets for a hotter spark. Timing set at 23 BTDC with 14 degrees...

ARC Billet Flywheels are CNC machined from 6061 T-6 aluminum. The Rare earth magnets (Neodymium) produce up to 17% more voltage at the coil. 30 degrees timing built into keyway. May require #5990...

ARC's new light weight Animal stroker flywheel for the Briggs PVL ignition. At 1.6lbs it is the lightest flywheel on the market for instant throttle response. SFI certified. Must be used with the...

ARC's new light weight Animal flywheel for the Briggs PVL ignition. At 1.6lbs it is the lightest flywheel on the market for instant throttle response. SFI certified. Must be used with the Briggs PVL...

Billet Connecting Rod 5.175 Briggs Vertical Model 28. This rod reqiures the removal of .050" material from the top of the piston. Inspection of piston is needed to assure there is sufficient...

3.625" Animal "Stroker" Rod with bearing inserts.ARC's +.237 stroker rod is designed to give you the most rod length you can get with the stock block and either an ARC 6580 Billet Crankshaft or a...

ARC Billet Connecting Rod Designed to be used in the models 40 and 44 Intek V-Twins with the Vertical Shaft. It is stock length and was designed to be used with stock pistons. They are CNC Machined...

Billet Rod 4.235" INTEK 305 StrokerStroker for JE pistons with 3" to 3.25" bore.Rod bolt torque: 170 in/lbs lubricated

Billet Rod ARC Pro Series. This rod is a stock replacement for the Briggs Intek 305 Model 20 engine. Featuring ARC's trademark forced oil dipper. CNC machined from aircraft grade 7075-T651 aluminum...

Billet Rod ARC Enduro Series CNC Machined from aircraft grade 7075 T-651 aluminum. Our 1" Stroker Rods are designed to handle the rigors of todays high horsepower Junior Dragster and open...

Hardened billet crank gear for the Briggs 5hp Raptor flathead. 1.005" I.D

Starter Nut for Flathead 5/8 x 18 thread pitch Stubby

2ft .070 Buna-n O-Ring for our 6052,6057 and 6058 Billet Sidecovers

ARC Billet Dual Bearing Sidecover kit for Briggs RaptorBy placing two bearings side-by-side on the PTO side of the crankshaft, we reduce crankflex by up to 40%. Flex is a major cause of crankshaft...

O-Ring Blockzilla Side Cover

This flywheel puller is designed for those who don't want to use the "knocker" method to remove their flywheel. Works with: ALL ARC Flywheels with Steel Adjustable Timing Hubs PVL Clone...

Precision in design and manufacturing, these are hardened lifters that will fit virtually all Briggs 5 hp blocks. The 6190 is .100" over stock in dimension.

Crank Bearing ID .875   OD 2.048   Width  .500Excellent Quality aftermarket "Trick" ball bearings can be used with a variety of stock Briggs and aftermarket single and dual...

This Crank Gear is a must when using an ARC #6580 Crankshaft or a Briggs #555204(495645) Crank.This is the gear to use for the Animal Stroker. 1.005" I.D.

This is the standard .998" bearing used on the flathead Briggs with Aluminum babbit. This bearing is also used on many stroker rods for other engines such as the Animal and GX200. Our connecting rod...

Fits ARC rods with stock stroke or stroker 1" (.9985") crankshaft journals. This is the standard bearing for "Stocker" 5 HP flathead rods. Also used in our 1" journal stroker rods for Jr. Dragsters...

Rod Bearing Briggs Vanguard